- Network configuration for ftp mac download#
- Network configuration for ftp mac mac#
- Network configuration for ftp mac windows#
Ultimately, your computer and the NMC will be on a peer to peer network which will allow for configuration as well. An alternative method to using the wizard via the network method may be to use a direct network connection between a computer and the NMC you are trying to configure and running the wizard. If using the wizard over the network, please note, the previously unconfigured NMC must be on the same subnet as the computer running the wizard. Any card with valid IP settings will have a solid green status LED. In addition, check the card you are trying to configure.
Network configuration for ftp mac mac#
You may want to check your DHCP client list for any MAC addresses beginning with 00 C0 B7, which indicates an APC address.
Please keep in mind that with certain firmware releases, the NMC can obtain a DHCP address and also prevent the wizard from working correctly. This utility supports NMC1/NMC2 cards that have firmware version 3.x.x or higher.
Network configuration for ftp mac download#
The Wizard is included on the CD bundled with the cards, and available to download from the APC website.
Network configuration for ftp mac windows#
The Device IP Configuration Wizard is a Windows application designed specifically to remotely configure the basic TCP/IP settings of Network Management Cards.
Smart-UPS front panel LCD - (available on supported SMT, SMX, and SRT Models with NMC2/NMC3)Ĭonfiguration Option 1 - Device IP Configuration Wizard. DHCP Option 12 - (NMC2 v5.1.5 or higher). Address Resolution Protocol (ARP) - (NMC1/NMC2/NMC3). Terminal Emulation (Local/Direct connection) - (NMC1/NMC2/NMC3). Device IP Configuration Wizard - (NMC1/NMC2/NMC3). In order to configure your Network Management Card-enabled device, select one of the available configuration methods listed below: They will obtain an IP address automatically so you may need to refer to your DHCP server to find out what IP address it obtained.Īll APC devices have a MAC address that begin with 00 C0 B7 which may help while reviewing your DHCP Client List. You can use the methods below to configure/access the card if you do not wish to use DHCP/BOOTP.ĭefault boot mode: DHCP Only - With DHCP Option 43 Vendor Cookie NOT required to accept DHCP Offer.īy default, all of APC's Network Management Card 2 and 3 based devices (such as an AP8XXX Next Gen Rack PDU (NMC2 only)) with AOS 5.1.1 or higher, are configured for DHCP Only with no vendor cookie required by default. If it is not configured on your DHCP server, the card will not accept an IP address. If using DHCP, a vendor cookie (DHCP Option 43) is required by default. In regards to Network Management Card 1 (AP9617, AP9618, AP9619) or devices with an embedded Network Management Card 1 (such as a AP78XX or AP79XX Rack PDU, Environmental Monitoring Unit, etc), there are three available options to configure the Network Management Card (NMC) with it's initial settings: the Wizard, terminal emulation (local/direct connection), and Address Resolution Protocol (ARP).ĭefault boot mode: DHCP/BootP - With DHCP Option 43 Vendor Cookie required to accept DHCP Offer.īy default, all of APC's Network Management Card 1 based devices are configured for a boot mode of DHCP/BOOTP. Network Management Card devices requiring reconfigurationĪ Network Management Card requires TCP/IP settings prior to being accessible via a network. Unconfigured Network Management Card-enabled devices. All firmware revisions (unless otherwise noted). Network Management Card 3 (NMC3) - AP9640, AP9641. Network Management Card 2 (NMC2) - AP9630/AP9630CH, AP9631/AP9631CH, AP9635/AP9635CHĭevices with an embedded Network Management Card 2 include (but are not limited to): 2G Metered/Switched Rack PDUs (AP84XX, AP86XX, AP88XX, AP89XX), Rack Automatic Transfer Switches (AP44XX), Certain Audio/Video Network Management Enabled products, Smart-UPS Online (SRT). Network Management Card 1 (NMC1) - AP9617, AP9618, AP9619ĭevices with an embedded Network Management Card 1 include (but are not limited to): Metered/Switched Rack PDUs (AP78XX, AP79XX), Rack Automatic Transfer Switches (AP77XX, Environmental Monitoring Units (AP9320, AP9340, NetBotz 200). There are multiple configuration options available, outlined below, for each family of Network Management Cards or devices that have embedded versions of these products.ĭevices with an embedded Web/SNMP Card include (but are not limited to): Environmental Monitoring Unit 1 (AP9312TH) Once the cards have been configured with an IP address, Subnet Mask, and Default Gateway the cards can be accessed, managed, and controlled from other computers on the network. NetShelter Metered-by-Outlet with Switching Rack PDUĪn APC Network Management Card must be configured with network settings before it can communicate on the network. 
NetShelter Shelving & Mounting Accessories
Sensors / Cameras / Licenses / Accessories Uniflair Ceiling Mounted Split Room Cooling
0 kommentar(er)
